Thank you for visiting Ham’s Life. Over the past 50 years plus Ham radio has been good to me. It has given me hours of enjoyment, opportunities for community service, help in saving lives, a career in radio & more. Here I will share some of my knowledge and experiences. Invite others you think would enjoy this blog.
If you are like me you hate harassing phone calls from telemarketers. They call and take you away from what you are doing but you try to be nice and tell them you are not interested. Then within a day or two they call again and then again.
Such misuse of the telephone has caused many people, when asked for their phone number, to give a false number. Sometimes they are real numbers just not the number of the person giving out that number. The result of that is someone else gets the call.
You may be wondering what this has to do with ham radio.
When taking a test for ham radio you are asked for your phone number. It is estimated that over half maybe as high as three quarters of the numbers given are incorrect numbers.
These numbers are used by the ARRL to send a message of congratulations to those who successfully pass the test. It is not necessary to enter any number so if you do not want to receive the message of congratulations from the ARRL just leave that space blank. It is just common courtesy.
As any regular reader of this blog knows, I firmly believe using ham radio during an emergency situation is of great importance in to the well being of our communities. Cell phones, land line telephone, and internet are very effective means of communication most of the time, but these all have a complex infrastructure and if that infrastructure fails, as it is very apt to do during an emergency, these means of communications become useless. Ham radio does not have an infrastructure so as long as some means of emergency power is available (sun, wind, water, hand cranked generator, etc) communications is possible. Many times in the past ham radio has been the only means of communications in and out of stricken areas, and without doubt it again will be many times in the future.
The ARRL sponsored ARES (Amateur Radio Emergency Services) provides a means whereby ham radio operators can facilitate a higher level of preparedness for themselves and their station. ARES provides training, information, and organization for emergency operation.
In the spirit of amateur radio emergency preparedness the Sacramento Valley ARES has put together a website which, though most specifically aimed at Sacramento Valley, will help any ham radio operator or group of hams to be more prepared. This includes ARES membership information, training resources, information on local nets, links to a variety of other related sites, and much more.
A few weeks ago a ham gave me a report on my 40 meter SSB signal quality. He told me that my carrier was fine but my audio was low. That is when it became obvious to me that either I had a problem with my transmitter or he did not understand what SSB was and I think it was the latter.
Normally the term SSB is used to mean Single-SideBand suppressed carrier (SSB-SC). In other words, if the transmitter is operating correctly there is no noticeable carrier. It is possible and legal to send a SSB signal with carrier but I have never heard this done on the ham bands.
When two alternating current signals are combined in a non-linear circuit they will product heterodynes of the sum and the differences of the signals.
(Heterodyne is an English word that is composed of two words of Greek origin. the first part, hetro, comes from the Greek word heteros [ἕτερος] which means another of a different kind. The second part of the word is dyne which comes from the Greek word dynamis [δύναμις]. The English word dynamite is also from δύναμις. It means force, power, or energy. When the two words are put together it means an energy or signal of a different kind or different frequency in this case.)
So if there is a 1 MHz signal mixed with a 1 KHz signal it will produce a third signal equal to the sum the two (1 MHz plus 1 KHz) or 1,001 KHz called the upper sideband. It will also produce an other signal equal to the difference of the two or 999 KHz (1 MHz minus 1 KHz) called the lower sideband. If the 1 MHz carrier is transmitted with the two side bands it will result in an Amplitude Modulated signal with a 1 KHz tone.
To send a SSB signal the carrier and one of the sidebands must be removed. The carrier is normally removed in the balanced modulator and the unwanted side band is removed by a filter.
There is a process of removing the carrier and unwanted sideband by phasing networks but I do not know of any modern transmitter that uses this process.
So when giving a signal report on someone’s SSB signal do not say the carrier is fine because if it has a carrier that is not good and they need to be told.
Many people consider history to be a very boring subject, but most regular readers of this blog probably realize that I have a certain fascination with history especially radio history.
If you are one of those who find history boring try thinking of it this way. Suppose you are lost in the woods and you don’t know how you got there. You seriously don’t think anyone knows where you are, or that anyone will notice your disappearance. Then a search team finds you. Wouldn’t you want to know how you ended up in the woods and how the search team knew too look for you and where to look?
That’s what history is all about. History tells us who we are, where we came from, and how we got to where we are today. It also tells us about the people who found the places, developed the philosophy, and invented the objects that make us who we are, and placed us where we are now.
Whether it is your ham radio, cell phone, television, broadcast radio, or other wireless device it started with Hertz’s spark. Electronic communications, which includes the telegraph and telephone, started earlier. Marconi did not invent the radio he just put together the wire, and wireless components that others had already invented and showed how they could be used for wireless communications.
I do not want to go back to the spark gap days of radio, but I do want to know what it was like for 6CC (later W6CC) who proctored my novice class test and for others of that era.
This morning I found a web site that not only describes the spark gap transmitter but even has some examples of how it sounded, both in Morse code and AM. Notice I said Morse code and not CW because spark gap transmissions were not CW (continuous wave) but it was a damped wave. This site explains the difference. The sight can be found at http://www.hammondmuseumofradio.org/spark.html (CLICK HERE).
Frequently I hear one ham tell another, while talking through an FM repeater, “your audio is low but maybe when you get closer it will come up.” That statement shows a lack of understanding about how FM works.
FM is short for Frequency Modulation. That means the intelligence, voice or other information, volume level is increased by increasing the deviation (the shift in frequency plus and minus from the un-modulated carrier frequency). One of the reasons FM is such a good mode of modulation when using a repeater is because the level of audio output remains constant after full capture (full quieting) of the repeaters receiver is achieved. So if the received signal is sufficient for full capture of the signal by the repeater’s receiver the audio will not increase or decrease with an increase or decrease of power reaching the receiver.
So if your audio is low and you have full quieting on the repeater output and you have not experienced that problem in the past using that repeater make the following checks.
Check the mike connector and mike cable. If possible change mikes to see if there is a change.
Check antenna connector, cable, and SWR to make sure no RF is getting into the audio stages and deteriorating their operation.
If your transmitter is capable of the new narrow band FM check to be sure the narrow band switch has not been toggled.
The deviation level of most modern transceivers can be adjusted by programming the desired deviation level. If your transceiver has such a programming feature then check to be sure it is correct. If deviation is set by an internal potentiometer it might be wise not to try to set the level without a deviation-meter.
If your transmitted audio is reported to be distorted and low check to be sure you are equipment is set to the proper frequency. It is easy to set the transmit frequency 5 KHz high or low in frequency and while the signal may still open up the repeater it will be distorted.
On September 13, 2013 Wayne S. Green II, W2NSD (Never Say Die”) became silent key.
Green was well known in the ham radio community as one who was not afraid to make his opinion known especially during the 1950s and 1960s. Amateur radio was not the only area where Wayne was willing to make his opinion known. He would speak on almost any subject and made a few guest appearances on the talk radio program Coast to Coast which is hosted by Art Bell, W6OBB.
Waynewas a strong advocate for SSB back when many of us (yes I was one) were dragging our feet and saying we liked AM. He was also a strong advocate for hams to move away from the glow in the dark technology into the solid state world. Green was a pioneer in ham radio FM and interfacing ham radios with computers.
Wayne Green was the chief honcho for CQ magazine for 5 years then from 1960 to 2003 he called himself the, “El Supremo and Founder”
73 Magazine encouraged hams to build their own equipment.
of 73 magazine.
ARRL CEO David Sumner, K1ZZ said, “Waynewill be remembered in many different ways by many different people, but he will be long remembered. He maintained his membership in the ARRL despite being a persistent critic. In the early days of packet radio he gave me some good advice as to how the ARRL should promote the new technology: ‘Talk about it as if everybody’s doing it, and eventually they will be.’”
Much more could be said about the accomplishments in amateur radio made by this icon as we say goodbye. He will be greatly missed
(The “Final” in his blog says, “Wayne Green passed away September 13, 2013 in a peaceful, painless transition from this life on Earth. An eternal optimist, and one who loved to share his never-ending zest for life, he was a friend to many and will be missed greatly. Wayne was not afraid of dying and was very much ready to embark on his next great adventure to the afterlife. http://www.waynegreen.com/wayne/news.html)
Are there times when amateur radio operators should be allowed to send encrypted messages? That is the question the FCC is asking. It can be found in Public Notice RM-11699 on the ARRL web site (www.arrl.org) and other ham radio web sites. It can also be found on the FCC website (http://apps.fcc.gov/ecfs/comment/view?id=6017446911).
If you have any opinion on the subject you can submit your comments to the FCC on their website at: http://apps.fcc.gov/ecfs/upload/display?z=uvxci
The first official Field Day operations were in 1933. This year marks the eightieth year sense that Field Day, but it was not the eightieth Field Day because there were several years during which ham radio operations were banned because of World War Two.
Many times a push pole is used to support an antenna on field day.
One of the most common mistakes made when trying to raise a push pole is first extending it to full length and then pull it up. That won’t work. You can see the results in this video: http://www.youtube.com/watch?v=H3aKS9eKwNQ. Someone can be heard in the background saying he thought the ground was too soft. That was not the reason for the failure.
The problem is when you are trying to raise the pole part of the pull is going to raise the antenna, and part of it is going to pushing down on the pole. The longer the pole is the greater the problem also with the pole fully collapsed there is the strength of each section so it can not bend and break.
A push pole should be fully collapsed when you raise it up then guy and secure the bottom section. Then use a ladder and first raise the upper most section by pushing it up out of the lower sections and tighten its set screw. Then raise the next highest section and tighten setscrew. If there is another section then push it up.
It really is a tricky project, and, if at all possible, you should have someone in the group who is experienced at raising push poles.
For more information see the “ARRL Field Day Handbook.”
Oleg Vladimirovich Losev (Russian: Олег Владимирович Лосев) was none other than the first person to record his findings in regards to Light Emitting Diodes (LED). Though he only lived to be 39 years old, May 10, 1903 – January 22, 1942, he had an impressive resume. Unfortunately for him, for Russia, and for electronic advances the Russian government did not take him seriously.
Oleg discovered that a carborundum (silicone/carbon compound) point-contact junction (cat’s whisker) diode used in crystal radios produced light when current was passed through it. Thus was the first LED. Oleg published his findings in a Russian Magazine in 1927but the LED was not a practical electronic component until 1962.
Mr. Losev also conducted experiments with negative resistance in semiconductor junctions and built the first solid-state amplifiers, oscillators, and superheterodyne radio receivers 25 years before the transistor was invented.
Just think of how much more advanced not only Amateur radio but all other radio services might be today if Oleg Losev had been taken seriously in his time. It just makes me wonder what our ham shacks would look like today.
In 1895, Alexander Stephanovich Popov built an improved version of a coherer-based radio receiver designed by Oliver Ledge. It proved to be a good lightning detector. Whether or not he used it in conjunction with a spark gap transmitter to demonstrate the transmission of a radio signal between two buildings on March 24, 1896 (Marconi did a public demonstration in September 1896) seems to be questionable. To this day Russia says that Popov, a Russian, was the inventor of the radio. One thing that can not be argued is that Oleg Vladimirovich Losev, a Russian, was the inventor of the LED.
I recently got an email from a long-time volunteer examiner (VE) who was upset because he had paid for the Extra course on HamTestOnline without knowing that would give it to him for free. Of course, I refunded his money, but it makes me wonder how many VEs still don’t know about our offer! Please help spread the word to your local VE team:HamTestOnline gives free Extra courses to all active General or Advanced class volunteer examiners for any VEC!